Check Flexure Strength
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Check the flexural strength of PSC section in a spreadsheet format table. Table Tool in midas Civil offers a variety of powerful built-in functions. Refer to Usage of Table Tool for detail directions. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
From the Main Menu select PSC > PSC Design Result Table > Check Flexure Strength |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
Upon executing the PSC Design Result Table > Check Flexure Strength, Records Activation Dialog prompts. Click Refer to Usage of Table Tool and check the following data:
When AASTHO LRFD-12 is selected Flexural strength is computed either as per clause 5.7.3.2 of AASTHO LRFD-12 or using strain compatibility depending upon the user input in PSC Design Parameters for flexural strength. Elem: Element number Part: Check location (I-End, J-End) of each element Positive/Negative: Positive moment, negative moment LCom. Name: Load combination name. Type: Displays the set of member forces corresponding to moving load case or settlement load case for which the maximum stresses are produced. If it is not defined then this field is left blank(-) By default, member forces due to moving load case or settlement load case are not concurrent. In order to consider the concurrent member forces, namely, Fx, Fy, Fz, Mx, My and Mz each having its MAX. and MIN value, the program computes FT, FB, FTL, FBL, FTR, FBR for all these twelve sets. For example: FT when Fx due to moving load is maximum is 30 N/mm2 and so on..
The set that results in maximum stress value FT, FB, FTL, FBL, FTR, FBR is displayed under 'Type' and the maximum stress value is displayed under FMAX. So as per above example, maximum stress value is 48, so it is displayed under FMAX, and it is from Fx-MIN set so under Type, Fx-MIN is displayed. All the values of this set will be displayed. CHK: Flexural strength check for element Muy: Factored moment acting at section about y axis Mcr: Cracking moment of section (Refer to the equation 5.7.3.3.2-1 of AASHTO LRFD (2012).) Mny: Nominal moment resistance of section about y axis PhiMny: Design moment resistance of section about y axis Flexural resistance is calculated by multiplying the distance from the neutral axis. (Refer to the clause 5.7.3.2.1 of AASHTO LRFD (2012).) If a tendon in tension is located at the upper part from the neutral axis under the sagging moment, the flexural resistance will have (-) sign and it will reduce the total moment resistance. where, Phi is resistance factor calculated as shown in the equation below. (Refer to the clause 5.5.4.2.1 of AASHTO LRFD (2012).) Ratio (Muy/PhiMny): Flexural resistance ratio, The verification is satisfied when it is less than 1.0. PhiMny/min(1.33Muy,Mcr): Verification of minimum reinforcement. The verification is satisfied when it is less than 1.0. If the verification of minimum reinforcement is not required, it will be displayed as 1.0. (Refer to the clause 5.7.3.3.2 of AASHTO LRFD (2012).) When AASTHO LRFD-07 is selected Flexural strength is computed either as per clause 5.7.3.2 of AASTHO LRFD-07 or using strain compatibility depending upon the user input in PSC Design Parameters for flexural strength. Elem: Element number Part: Check location (I-End, J-End) of each element Positive/Negative: Positive moment, negative moment LCom. Name: Load combination name. Type: Displays the set of member forces corresponding to moving load case or settlement load case for which the maximum stresses are produced. If it is not defined then this field is left blank(-) By default, member forces due to moving load case or settlement load case are not concurrent. In order to consider the concurrent member forces, namely, Fx, Fy, Fz, Mx, My and Mz each having its MAX. and MIN value, the program computes FT, FB, FTL, FBL, FTR, FBR for all these twelve sets. For example: FT when Fx due to moving load is maximum is 30 N/mm2 and so on..
The set that results in maximum stress value FT, FB, FTL, FBL, FTR, FBR is displayed under 'Type' and the maximum stress value is displayed under FMAX. So as per above example, maximum stress value is 48, so it is displayed under FMAX, and it is from Fx-MIN set so under Type, Fx-MIN is displayed. All the values of this set will be displayed. CHK: Flexural strength check for element Muy: Factored moment acting at section about y axis. Mcr: Cracking moment of section. Mny: Nominal moment resistance of section about y axis. PhiMny: Factored moment of resistance of section about y axis. (Phi assumed as 1.0) PhiMny/1.33Muy: Ratio of factored moment of resistance to factored moment acting on section about y axis. PhiMny/1.2Mcr: Ratio of factored moment of resistance to cracking moment of section.
When CSA-S6S1-2010 is selected Flexural strength is computed either as per clause 8.8.4.2 of CSA-S6S1-2010 or using strain compatibility depending upon the user input in PSC Design Parameters for flexural strength. Elem: Element number Part: Check location (I-End, J-End) of each element Positive/Negative: Positive moment, negative moment LCom. Name: Load combination name. Type: Displays the set of member forces corresponding to moving load case or settlement load case for which the maximum stresses are produced. If it is not defined then this field is left blank(-) By default, member forces due to moving load case or settlement load case are not concurrent. In order to consider the concurrent member forces, namely, Fx, Fy, Fz, Mx, My and Mz each having its MAX. and MIN value, the program computes FT, FB, FTL, FBL, FTR, FBR for all these twelve sets. For example: FT when Fx due to moving load is maximum is 30 N/mm2 and so on..
The set that results in maximum stress value FT, FB, FTL, FBL, FTR, FBR is displayed under 'Type' and the maximum stress value is displayed under FMAX. So as per above example, maximum stress value is 48, so it is displayed under FMAX, and it is from Fx-MIN set so under Type, Fx-MIN is displayed. All the values of this set will be displayed. CHK: Flexural strength check for element Mf: Factored moment acting at section about y axis Mcr: Cracking moment of section (Refer to the clause 8.8.4.4 of CSA-S6S1-2010.) Mr: Design moment resistance of section about y axis Flexural resistance is calculated by multiplying the distance from the neutral axis. (Refer to the clause 8.8.3 of CSA-S6S1-2010.) If a tendon in tension is located at the upper part from the neutral axis under the sagging moment, the flexural resistance will have (-) sign and it will reduce the total moment resistance. where, Phi is material resistance factor as shown in the table below. (Refer to the table 8.1 of CSA-S6S1-2010.) Ratio (Mf/Mr): Flexural resistance ratio. The verification is satisfied when it is less than 1.0. min(4/3Mf,1.2Mcr)/Mr: Verification of minimum reinforcement ratio. The verification is satisfied when it is less than 1.0. (Refer to the clause 8.8.4.3 of CSA-S6S1-2010.) C/D: Verification of maximum reinforcement ratio. The verification is satisfied when it is less than 0.5. (Refer to the clause 8.8.4.5 of CSA-S6S1-2010.) When EUROCODE2-2:05 is selected Elem: Element number Part: Check location (I-End, J-End) of each element Positive/Negative: Positive moment, negative moment LCom. Name: Load combination name. Type: Displays the set of member forces corresponding to moving load case or settlement load case for which the maximum stresses are produced. If it is not defined then this field is left blank(-) By default, member forces due to moving load case or settlement load case are not concurrent. In order to consider the concurrent member forces, namely, Fx, Fy, Fz, Mx, My and Mz each having its MAX. and MIN value, the program computes FT, FB, FTL, FBL, FTR, FBR for all these twelve sets. For example: FT when Fx due to moving load is maximum is 30 N/mm2 and so on..
The set that results in maximum stress value FT, FB, FTL, FBL, FTR, FBR is displayed under 'Type' and the maximum stress value is displayed under FMAX. So as per above example, maximum stress value is 48, so it is displayed under FMAX, and it is from Fx-MIN set so under Type, Fx-MIN is displayed. All the values of this set will be displayed. CHK: Flexural strength check for element M_Ed: Design moment M_Rd: Moment resistance. Mny: Nominal moment resistance of section about y axis. As,min: Minimum required reinforcing steel area. |
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|