.jpg)
Function
Use this function to modify a part of the steel material property data entered during the creation of the analysis model or to change the entered material property data pertaining to specific design requirements.
Call
From the Main Menu select Design > Steel Design Parameter > Modify Steel Material.
From the Menu tab of the Tree Menu select Design > Steel Design Parameter > Modify Steel Material.
Entry
Use the following dialog box to enter the data (refer to Note 1):
Material ListDisplay the material properties of steel entered during the creation of the analysis model. Select the material to be modified or changed with the mouse.
Steel Material SelectionDisplay the selected material so that the property data can be modified or changed.
The material property data can be changed by using the material property database in the program or by directly entering the changed data.
Method
for using material property database
Select the material name and the code in which the relevant material is
defined, with the mouse.
Direct
entry by the user
Select 'None' in the Code field and enter the name of the material in the
Name field. Once these entries are made, all the material property data
fields are activated for data entry (refer to Note 2).
Modulus of Elasticity (Es): Modulus of elasticity of steel
Poisson's Ratio (Ps): Poisson's ratio of steel
Tensile Strength (Fu): Tensile strength of steel
Yield Strength (Fy)
Yield strength of members with thicknesses thinner than 40mm (refer to
Note 3)
Yield Strength
[t > 40mm] (Fy2)
Yield strength for which the thickness of the members in use is thicker
than 40mm (refer to Note 3)
.jpg)
: Modify the relevant
material property data by replacing with the values entered by the user.
.jpg)
: Do not enter the values
or the selection and close the dialog box.
Note
1
When the Name, Es, Ws, Fy1 and Fy2 are not entered in the analysis model,
the following data are applied by default :
Name = A36
Es = 4.176+E9 lb/ft2 (29,000 ksi)
Ws = 490 lb/ft3
Fy1 = 250 lb/ft2 (36 ksi)
Fy2 = 250 lb/ft2 (36 ksi)
Note
2
The steel material standards are classified into None, ASTM(S),CSA(s),
BS(S), DIN(S), EN(S), JIS(S), GB(S), JGJ(S), KS(S), KS-Civil(S).
Note
3
The Fy-a, Fy-b, Fy-c and Fy-d values below represent the steel yield strengths
and are used to calculate the allowable stress (design strength) for each
stress component (compression, tension, bending and shear) during the
strength verification. The maximum thickness of a member determines the
application of Fy-a, Fy-b, Fy-c and Fy-d for the calculation of the allowable
stress (design stress). The heading, Fy-a, Fy-b, Fy-c and Fy-d (simply
expanded to demonstrate the variation) listed below do not necessarily
correspond to the heading in the dialog box.
(1) ASTM(S)
- Es = 29000 kips/in2
- Fy (kips/in2)
|
Material type |
Fy-a |
|
A36 |
36. |
|
A53 |
35. |
|
A242-40 |
40. |
|
A242-42 |
42. |
|
A242-46 |
46. |
|
A242-50 |
50. |
|
A441-40 |
40. |
|
A441-42 |
42. |
|
A441-46 |
46. |
|
A441-50 |
50. |
|
A500-33 |
33. |
|
A500-39 |
39. |
|
A500-42 |
42. |
|
A500-46 |
46. |
|
A500-50 |
50. |
|
A501 |
36. |
|
A514-90 |
90. |
|
A514-100 |
100. |
|
A529-42 |
42. |
|
A529-50 |
50. |
|
A570-40 |
40. |
|
A570-42 |
42. |
|
A572-42 |
42. |
|
A572-50 |
50. |
|
A572-60 |
60. |
|
A572-65 |
65. |
|
A588-40 |
40. |
|
A588-42 |
42. |
|
A588-46 |
46. |
|
A588-50 |
50. |
|
A606-45 |
45. |
|
A606-50 |
50. |
|
A607-45 |
45. |
|
A607-50 |
50. |
|
A607-55 |
55. |
|
A607-60 |
60. |
|
A607-65 |
65. |
|
A607-70 |
70. |
|
A618-50 |
50. |
|
A852 |
70. |
(2)
CSA(S)
- Es = 200000 N/mm2
- Fy (N/mm2)
|
Material type |
Fy-1 |
Fy-2 |
Fy-3 |
|
230G(H) |
230. |
230. |
230. |
|
350G(H) |
350. |
350. |
350. |
|
400G(H) |
400. |
400. |
400. |
|
260W(H) |
260. |
260. |
260. |
|
300W(H) |
300. |
290. |
280. |
|
350W(H) |
350. |
330. |
320. |
|
380W(H) |
380. |
380. |
380. |
|
400W(H) |
400. |
400. |
400. |
|
480W(H) |
480. |
480. |
480. |
|
260WT(H) |
260. |
260. |
260. |
|
300WT(H) |
300. |
290. |
290. |
|
350WT(H) |
350. |
330. |
330. |
|
380WT(H) |
380. |
380. |
380. |
|
400WT(H) |
400. |
400. |
400. |
|
480WT(H) |
480. |
480. |
480. |
|
350R(H) |
350. |
350. |
350. |
|
350A(H) |
350. |
350. |
350. |
|
400A(H) |
400. |
400. |
400. |
|
480A(H) |
480. |
480. |
480. |
|
350AT(H) |
350. |
350. |
350. |
|
400AT(H) |
400. |
400. |
400. |
|
480AT(H) |
480. |
480. |
480. |
|
700Q(H) |
700. |
700. |
700. |
|
700QT(H) |
700. |
700. |
700. |
|
230G(C) |
230. |
230. |
230. |
|
350G(C) |
350. |
350. |
350. |
|
400G(C) |
400. |
400. |
400. |
|
260W(C) |
260. |
260. |
260. |
|
300W(C) |
300. |
290. |
280. |
|
350W(C) |
350. |
330. |
320. |
|
380W(C) |
380. |
380. |
380. |
|
400W(C) |
400. |
400. |
400. |
|
480W(C) |
480. |
480. |
480. |
|
260WT(C) |
260. |
260. |
260. |
|
300WT(C) |
300. |
290. |
290. |
|
350WT(C) |
350. |
330. |
330. |
|
380WT(C) |
380. |
380. |
380. |
|
400WT(C) |
400. |
400. |
400. |
|
480WT(C) |
480. |
480. |
480. |
|
350R(C) |
350. |
350. |
350. |
|
350A(C) |
350. |
350. |
350. |
|
400A(C) |
400. |
400. |
400. |
|
480A(C) |
480. |
480. |
480. |
|
350AT(C) |
350. |
350. |
350. |
|
400AT(C) |
400. |
400. |
400. |
|
480AT(C) |
480. |
480. |
480. |
|
700Q(C) |
700. |
700. |
700. |
|
700QT(C) |
700. |
700. |
700. |
- Max. thickness for applying Fy (mm)
Hollow Structural Sections
|
Material type |
Fy-1 |
Fy-2 |
Fy-3 |
|
300W |
16.0 |
|
|
|
350W, 350WT |
16.0 |
|
|
|
380W, 380WT |
16.0 |
|
|
|
350A, 350AT |
16.0 |
|
|
Plates, Bars and Welded Shapes
|
Material type |
Fy-1 |
Fy-2 |
Fy-3 |
|
350R |
14.0 |
|
|
|
400W, 400WT |
20.0 |
|
|
|
480W, 480WT |
20.0 |
|
|
|
480A, 480AT |
20.0 |
|
|
|
350G, 400G |
30.0 |
|
|
|
400A, 400AT |
40.0 |
|
|
|
700Q, 700QT |
50.0 |
|
|
|
350WT |
40.0 |
60.0 |
100.0 |
|
260W, 260WT |
40.0 |
65.0 |
100.0 |
|
300W, 300WT |
40.0 |
65.0 |
100.0 |
|
350W, 350WT |
40.0 |
65.0 |
100.0 |
|
350A, 350AT |
40.0 |
65.0 |
100.0 |
|
230G |
40.0 |
65.0 |
300.0 |
Rolled Shapes and Sheet Piling (G=Group)
|
Material type |
Fy-1 |
Fy-2 |
Fy-3 |
|
350R |
G1 |
|
|
|
400W |
G1 |
|
|
|
480W, 480WT |
G1 |
|
|
|
400WT |
G1,2 |
|
|
|
400A, 400AT |
G1,2 |
|
|
|
300W |
G1,2 |
G3 |
|
|
350G, 400G |
G1,2 |
G3 |
|
|
350WT |
G1,2 |
G3,4 |
|
|
260W |
G1,2 |
G3,4 |
|
|
230G |
G1,2 |
G3,4 |
G5 |
|
260WT, 300WT |
G1,2 |
G3,4 |
G5 |
|
350A, 350AT |
G1,2 |
G3,4 |
G5 |
(3)
BS(S)
- Es = 205000 N/mm2
- Fy (N/mm2)
|
Material type |
Fy-a |
Fy-b |
Fy-c |
Fy-d |
|
43A |
275. |
265. |
255. |
245. |
|
43B |
275. |
265. |
255. |
245. |
|
43B(T) |
275. |
265. |
255. |
245. |
|
43C |
275. |
265. |
255. |
245. |
|
43D |
275. |
265. |
255. |
245. |
|
43DD |
275. |
265. |
255. |
245. |
|
43E |
275. |
265. |
255. |
245. |
|
43EE |
275. |
265. |
255. |
245. |
|
50A |
355. |
345. |
340. |
325. |
|
50B |
355. |
345. |
340. |
325. |
|
50B(T) |
355. |
345. |
340. |
325. |
|
50C |
355. |
345. |
340. |
325. |
|
50D |
355. |
345. |
340. |
325. |
|
50DD |
355. |
345. |
340. |
325. |
|
50E |
355. |
345. |
340. |
325. |
|
50EE |
355. |
345. |
340. |
325. |
|
50F |
355. |
345. |
340. |
325. |
|
55C |
450. |
430. |
415. |
400. |
|
55EE |
450. |
430. |
415. |
400. |
|
55F |
450. |
430. |
415. |
400. |
|
WR50A |
355. |
355. |
355. |
355. |
|
WR50B |
355. |
355. |
355. |
355. |
|
WR50C |
355. |
355. |
355. |
355. |
- Max. thickness for applying Fy (mm)
|
Material type |
Fy-a |
Fy-b |
Fy-c |
Fy-d |
|
43,50 Series |
16.0 |
40.0 |
63.0 |
100.0 |
|
55 Series |
16.0 |
25.0 |
40.0 |
63.0 |
(4) DIN(S)
- Es = 210000 N/mm2
- Fy (N/mm2)
|
Material type |
Fy-a |
Fy-b |
|
St37-2 |
240. |
215. |
|
USt37-2 |
240. |
215. |
|
RSt37-2 |
240. |
215. |
|
St52-3 |
360. |
325. |
|
StE355 |
360. |
325. |
|
WStE355 |
360. |
325. |
|
TStE355 |
360. |
325. |
|
EStE355 |
360. |
325. |
|
GS-52 |
260. |
260. |
|
GS-20Mn5 |
260. |
260. |
|
C35N |
300. |
270. |
- Max. thickness for applying Fy (mm)
|
Material type |
Fy-a |
Fy-b |
|
GS Series |
100.0 |
- |
|
C35N |
16.0 |
80.0 |
|
Others |
40.0 |
80.0 |
(5)
EN(S)
- Es = 210000 N/mm2
- Fy (N/mm2)
|
Material type |
Fy-a |
Fy-b |
|
S235 |
235. |
215. |
|
S275 |
275. |
255. |
|
S355 |
355. |
335. |
|
S420 |
420. |
390. |
|
S460 |
460. |
430. |
|
Fe360 |
235. |
215. |
|
Fe430 |
275. |
255. |
|
Fe510 |
355. |
335. |
|
FeE275 |
275. |
255. |
|
FeE355 |
355. |
355. |
|
S420M |
420. |
390. |
|
S460M |
460. |
430. |
- Max. thickness for applying Fy (mm)
|
Material type |
Fy-a |
Fy-b |
|
All other Series |
40.0 |
100.0 |
(5)
JIS(S)
- Es = 205000 N/mm2
- Fy (N/mm2)
|
Material type |
Fy-a |
Fy-b |
|
SN400A |
235. |
215. |
|
SN400B |
235. |
215. |
|
SN400C |
235. |
215. |
|
SN490B |
325. |
295. |
|
SN490C |
325. |
295. |
|
SS400 |
235. |
215. |
|
STK400 |
235. |
215. |
|
STKR400 |
235. |
215. |
|
SSC400 |
235. |
215. |
|
SS490 |
275. |
255. |
|
SS540 |
370. |
370. |
|
SM400 |
235. |
215. |
|
SMA400 |
235. |
215. |
|
SM490 |
325. |
295. |
|
SM490Y |
325. |
295. |
|
SMA490 |
325. |
295. |
|
STK490 |
325. |
295. |
|
STKR490 |
325. |
295. |
|
SM520 |
355. |
355. |
|
SCW410-CF |
235. |
235. |
|
SCW480-CF |
275. |
275. |
|
SCW490-CF |
315. |
315. |
|
SCW520-CF |
355. |
355. |
- Max. thickness for applying Fy (mm)
|
Material type |
Fy-a |
Fy-b |
|
All other Series |
40.0 |
100.0 |
(6)
GB(S)
- Es = 206000 N/mm2
- Fy (N/mm2)
|
Material type |
Fy-1 |
Fy-2 |
Fy-3 |
|
Grade3 |
235. |
225. |
215. |
|
16Mn |
345. |
325. |
295. |
|
16Mnq |
345. |
325. |
295. |
|
15MnV |
390. |
370. |
350. |
|
15MnVq |
390. |
370. |
350. |
- Max. thickness for applying Fy (mm)
|
Material type |
Fy-1 |
Fy-2 |
Fy-3 |
|
Grade3 |
|
|
|
|
Round, square and flat |
40.0 |
100.0 |
|
|
Angles, channel and I-shapes |
15.0 |
20.0 |
Over 20.0 |
|
Plates |
20.0 |
40.0 |
50.0 |
|
Other Series |
16.0 |
25.0 |
36.0 |
(7)JGJ(S)
- Es = 206000 N/mm2
- Fy (N/mm2)
|
Material type |
Fy-1 |
Fy-2 |
Fy-3 |
Fy-4 |
|
Q235 |
235. |
225. |
215. |
205. |
|
Q295 |
295. |
275. |
255. |
235. |
|
Q345 |
345. |
325. |
295. |
275. |
|
Q390 |
390. |
370. |
350. |
330. |
|
Q420 |
420. |
400. |
380. |
360. |
- Max. thickness for applying Fy (mm)
|
Material type |
Fy-1 |
Fy-2 |
Fy-3 |
Fy-4 |
|
Q235 |
16.0 |
40.0 |
60.0 |
100.0 |
|
Other Series |
16.0 |
35.0 |
50.0 |
100.0 |
(8)JTJ(S)
- Es = 210000 N/mm2
- Fy (N/mm2)
|
Material type |
Fy-1 |
Fy-2 |
Fy-3 |
Fy-4 |
|
A3 |
240. |
240. |
240. |
240. |
|
16Mn |
345. |
325. |
315. |
295. |
- Max. thickness for applying Fy (mm)
|
Material type |
Fy-1 |
Fy-2 |
Fy-3 |
Fy-4 |
|
16Mn |
16.0 |
25.0 |
36.0 |
50.0 |
(9)
KS(S)
- Es = 2100 tonf/cm2
- Fy (tonf/cm2)
|
Material type |
Fy-a |
Fy-b |
|
SS41 |
2.4 |
2.2 |
|
SPS41 |
2.4 |
2.2 |
|
SPSR41 |
2.4 |
2.2 |
|
SS50 |
2.8 |
2.6 |
|
SS55 |
3.8 |
3.8 |
|
SS400 |
2.4 |
2.2. |
|
SPS400 |
2.4 |
2.2 |
|
SPSR400 |
2.4 |
2.2 |
|
SS490 |
2.8 |
2.6 |
|
SS540 |
3.8 |
3.8 |
|
SWS41 |
2.4 |
2.2 |
|
SWS50 |
3.3 |
3.0 |
|
SWS50Y |
3.3 |
3.0 |
|
SPS50 |
3.3 |
3.0 |
|
SPSR50 |
3.3 |
3.0 |
|
SWS53 |
3.6 |
3.4 |
|
SWS58 |
4.1 |
4.1 |
|
SWS400 |
2.4 |
2.2 |
|
SWS490 |
3.3 |
3.0 |
|
SWS490Y |
3.3 |
3.0 |
|
SWS490TMC |
3.3 |
3.3 |
|
SWS520 |
3.6 |
3.4 |
|
SWS520TMC |
3.6 |
3.6 |
|
SWS570 |
4.1 |
4.1 |
|
SWS520(LSD) |
3.6 |
3.3 |
|
SWS570(LSD) |
4.3 |
4.3 |
|
SM400 |
2.4 |
2.2 |
|
SM490Y |
3.3 |
3.0 |
|
SMA490 |
3.3 |
3.0 |
|
SCW490-CF |
3.3 |
3.0 |
|
SPS490 |
3.3 |
3.0 |
|
SPSR490 |
3.3 |
3.3 |
|
SM490TMC |
3.3 |
3.3 |
|
SM520 |
3.6 |
3.4 |
|
SM520TMC |
3.6 |
3.6 |
|
SM570 |
4.1 |
4.1 |
|
SM520(LSD) |
3.6 |
3.3 |
|
SM570(LSD) |
4.3 |
4.3 |
|
SMA41 |
2.4 |
2.2 |
|
SMA50 |
3.3 |
3.0 |
|
SMA58 |
4.1 |
4.1 |
|
SSC400 |
2.4 |
2.4 |
|
ZSS400 |
3.0 |
3.0 |
- Max. thickness for applying Fy (mm)
|
Material type |
Fy-a |
Fy-b |
|
490-CF |
8.0 |
60.0 |
|
490TMC |
40.0 |
80.0 |
|
Others |
40.0 |
100.0 |
(9) KS-Civil(S)
- Es = 2100 tonf/cm2
- Fy (tonf/cm2)
|
Material type |
Fy-a |
Fy-b |
Fy-c |
|
SS41 |
2.4 |
2.2 |
2.2 |
|
SPS41 |
2.4 |
2.2 |
2.2 |
|
SPS50 |
3.2 |
3.0 |
3.0 |
|
SS400 |
2.4 |
2.2 |
2.2 |
|
SPS400 |
2.4 |
2.2 |
2.2 |
|
SPS490 |
3.2 |
3.0 |
3.0 |
|
SWS41 |
2.5 |
2.4 |
2.2 |
|
SWS50 |
3.3 |
3.2 |
3.0 |
|
SWS50Y |
3.7 |
3.6 |
3.4 |
|
SWS53 |
3.7 |
3.6 |
3.4 |
|
SWS58 |
4.7 |
4.6 |
4.4 |
|
SWS400 |
2.5 |
2.4 |
2.2 |
|
SWS490 |
3.3 |
3.2 |
3.0 |
|
SWS490Y |
3.7 |
3.6 |
3.4 |
|
SWS520 |
3.7 |
3.6 |
3.4 |
|
SWS570 |
4.7 |
4.6 |
4.4 |
|
SM400 |
2.4 |
2.2 |
2.2 |
|
SM490 |
3.2 |
3.0 |
3.0 |
|
SM490Y |
3.6 |
3.4 |
3.3 |
|
SM520 |
3.6 |
3.4 |
3.3 |
|
SM570 |
4.6 |
4.4 |
4.3 |
|
SMA41 |
2.4 |
2.2 |
2.2 |
|
SMA50 |
3.6 |
3.4 |
3.3 |
|
SMA58 |
4.6 |
4.4 |
4.3 |
|
SMA400 |
2.4 |
2.2 |
2.2 |
|
SMA490 |
3.6 |
3.4 |
3.3 |
|
SMA570 |
4.6 |
4.4 |
4.3 |
- Max. thickness for applying Fy (mm)
|
Material type |
Fy-a |
Fy-b |
Fy-c |
|
SS, SM |
40.0 |
75.0 |
100.0 |
|
Others |
16.0 |
40.0 |
40.0 |
Note 4
When “None” is specified in the Code entry field, design can
be performed by using the user defined material properties.