Data Conversion

Convert model data and analysis results of midas Gen into model data or loads for midas SDS, or vice versa. midas SDS is a specialized program for floor/mat plate analysis.

Structural Frame Systems, Floor Systems and Foundation Systems are generally separated for structural analysis and design.

In such cases, analysis data for both systems must be prepared separately. Data Conversion allows the user to avoid such duplication and transfer the geometry and load data back and forth between the frame and floor/mat design analyses. The Data Conversion feature is especially useful for residential reinforced concrete structures with flat plates and irregular shear/bearing walls.

Data Conversion of midas Gen performs the following functions:

1. The coordinates of the floor framing from the midas Gen framing model data are extracted. midas Gen data are converted into midas SDS model data (midas Gen-> midas SDS, Model Data). Equivalent stiffness of beams, columns, diagonals and walls of the frame model connected to the floor plate are automatically calculated and entered as elastic support conditions in the floor plate analysis model. For the analysis of a foundation mat, wall elements are converted into beam elements of equivalent stiffness. The stiffness of elastic supports is not generated automatically

2. The midas SDS reaction data resulting from the floor plate analysis are automatically entered as load data in the midas Gen frame model (midas SDS->midas Gen, Load Data).  

3. The support reactions resulting from the midas Gen analysis are automatically converted into midas SDS model load data for foundation mat analysis. (midas Gen->midas SDS, Reaction Data)

To use Data Conversion, story data must be previously entered to assign the floor plate subjected to conversion.

The elements in a frame model to be converted into a floor plate model may be beam elements on the same plane, beam or truss elements (columns or diagonals) connected to the plane and wall elements. The floor plate elements and the analysis data must be additionally entered in midas SDS using the Object.

The following data are created during a conversion process, from a midas Gen frame model into a midas SDS floor plate analysis model:

Note

1. For wall elements, a beam element with an equivalent wall stiffness is additionally created to connect the ends of a wall element. The beam element is required to maintain the connectivity between vertical line springs, which constitute a line elastic support.

2. Refer to midas SDS On-line Manual for the features of midas SDS.

When the midas SDS analysis is completed, the nodal load data of midas Gen are created using Data Conversion once again.

The method of converting the reaction data of the midas SDS floor plate analysis model into nodal load data of midas Gen is as follows:

The reactions at the point-elastic supports representing column or diagonal members are converted into nodal loads (vertical concentrated loads or moments) of midas Gen.

The reactions at the line spring supports representing wall elements are transformed into two point reactions at both ends of walls as if the walls were simply supported beams.

The midas Gen reaction data at the supports are converted into midas SDS concentrated load data as below.

From the Main Menu select File > Data Conversion > midas Gen –> midas SDS (Model + Reaction Data).

From the Main Menu select File > Data Conversion > midas SDS –> midas Gen(Load Data).

Convert a midas Gen model into a midas SDS model data for a floor. The conversion serves to create a midas SDS floor plate or foundation mat analysis model in the structural analysis of a residential building with irregular shear wall layout.

midas SDS File Name( *.MST)

Enter a midas SDS model data file name (fn.MST), which is to be created as a text type.

Convert for Slab/Foundation

Assign whether the midas SDS model data to be created is for a floor slab of a foundation mat.

Select Story for Convert to midas SDS

Enter a story of the midas Gen model to convert into a midas SDS model.

Select the lowest floor (base) if a foundation mat model is to be created.

Bending Stiffness Factor

Enter the bending stiffness factor for elements. The data entry is not required for creating foundation mat models.

Note

When a floor plate model is created through Data Conversion, the elastic support stiffness of Column and Wall Supports is automatically calculated as follows:

Axial Stiffness

The floor height of the story below the relevant floor plate is considered for axial stiffness, SDz.

Where,

  Modulus of elasticity

Cross sectional area

Floor height

Bending stiffness

Bending stiffness, Sr, is computed on the basis of the floor heights above and below the floor plate in question.

Where,

: Stiffness correction factor that reflects the lengths of vertical members beyond the immediate floors above and below.

Modulus of elasticity of the upper and lower members

  Moments of inertia of the upper and lower members

Upper and lower level heights

The '' represents the member's bending stiffness and is determined on the basis of the total number of stories of the structure, the position of the floor plate in question, the connection conditions, etc. In the case of a multi-story building, the following table values are typically used.

For diagonal members, the horizontal component of the above stiffness is neglected and only the vertical component is considered.

For wall elements, the above bending stiffness is applied to the weak axis.

The axial and flexural stiffness of the columns and diagonals thus calculated is converted into point elastic support springs at the relevant positions. In the case of wall elements, the stiffness is considered by linear elastic support springs between the ends.

 Additional beam elements are entered to ensure the connectivity of the ends of wall elements.

The reaction data of the point elastic support springs calculated from the program are automatically entered as nodal concentrated loads on the frame model through Data Conversion. The reactions of linear elastic support springs are entered as equivalent concentrated loads at both ends of wall elements.

<Table> Bending stiffness factor, , for column, diagonal and wall elements

*For structures higher than 10 stories, use the values specified in the table for the portions between 2nd and 4th stories and between (roof -4) and roof floors. Use 6.0 for the portion between 5th and (roof -5).

* Assumptions

the heights of all the stories are identical
the cross sectional areas of columns (or walls) of all the stories are identical
the thickness of floor plates and column capitals are neglected

Note

If Convert for Foundation is selected, the reactions resulting from the structural analysis of a midas Gen frame model are converted into load data of a midas SDS model. The reactions for each load case of the midas Gen model are automatically entered as point loads including the results of response spectrum analysis. As a result, the signs deleted during the process of load combinations for modal analysis must be reproduced.
(Refer to "Response Spectrum Analysis Control")

The reactions resulting from midas SDS floor plate analysis are converted into load data for midas Gen frame structural model.

midas SDS File Name(*.SA1, *.BN2)

Enter the name of the midas SDS floor plate analysis model to be converted into load data.

Select Stories for Nodal Loads

Convert the reactions of the floor plate analysis model into load data for midas Gen frame structural model. Select the floors onto which the reaction data are to be loaded. Multiple selection is feasible.